Product ID:ALKYD ENAMEL,GLOSS,GRAY 16492
MSDS Date:09/22/1986
FSC:8010
NIIN:00-582-1508
MSDS Number: BHWZL

CON-LUX COATINGS, INC.

226 TALMAGDE ROAD
EDISON, NJ 08818-0847
US

Emergency Phone: (206) 287-4000

Info Phone: (206) 287-4000

Cage: 60189

CON-LUX COATINGS INC

847 EDISON, NJ 08818-0847 US

Telephone: 732-287-4000

Cage: 60189

MINERAL SPIRITS

Fraction By Weight: 25.13%

OSHA PEL 100 PPM

TITANIUM DIOXIDE

CAS: 13463-67-7

RTECS: XR2275000

Fraction By Weight: NO

OSHA PEL 15 MG/M3 TDUST

ACGIH TLV: 10 MG/M3 TDUST; 9293

Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Effects of Overexposure:HEADACHE, NAUSEA & DIZZINESS.

First Aid:INHALATION: REMOVE TO FRESH AIR.RESTORE RESPIRATION IF
NECESSARY. EYE CONTACT: FLUSH IMMEDIATELY W/COPIOUS QTYS OF WTR
FOR 15 MINS MINIMUM. CONSULT PHYSICIAN. DERMAL CONTACT: WASH
AFFECTED AREA W/SOA P & WTR.REMOVE CONTAMINATED CLOTHING CONSULT
PHYSICIAN IS IRRITATION PERSISTS. INGESTION: DRINK 1/2 GLASSES WTR
TO DILUTE.DO NOT INDUCE VOMITING.IF VOMITING OCCURS KEEP HEAD BELOW
KNEE LEVEL.

Flash Point Method:TCC
Flash Point:105F
Lower Limits:1.0
Extinguishing Media:FOAM,CARBON DIOXIDE CO2,DRY CHEMICAL,WATER MIST
Fire Fighting Procedures:SMOTHER FLAMES W/ONE OF THE ABOVE
EXTINGUISHING MEDIA.WATER MAY BE USED TO COOL DOWN UNOPENED
CONTAINERS IN VICINITY.
Unusual Fire/Explosion Hazard:CONTAINS FLAMMABLE SOLVENT.DO NOT USE IN
AREAS WHERE SPARKS OR OPEN FLAMES ARE PRESENT.

Spill Release Procedures:ELIMINATE ALL IGNITION SOURCES.WEAR
APPROPRIATE PERSONAL PROTECTION EQUIP & APPROVED RESPIRATOR.CONTAIN
SPILL W/ABSORBENT MATERIAL & PUT INTO VAPOR TIGHT
CONTAINERS.PREVENT MATERIAL FROM CONTACTING ANY WTR SOURCES OR
SEWERS LEADING TO SURFACE WTRS.

Handling and Storage Precautions:STORE IN AREAS DESIGNED TO COMPLY
W/ANSI/NFPA 30 FLAMMABLE & COMBUSTIBLE LIQUIDS CODE.
Other Precautions:GROUND CONTAINERS WHEN POURING LIQS/PDRS TO AVOID
STATIC CHARGE BUILD UP.DO NOT HANDLE UNTIL MANUFACTURERS SAFETY
PRECAUTIONS HAVE BEEN READ & UNDERSTOOD.PROVIDE ADEQUATE
VENTILATION OR RESPIRATORY PR OTECTION DURING WELDING/FLAME
CUTTING.

Respiratory Protection:IN OUTDOOR OR OPEN AREAS,USE APPROVED RESPIRATOR
TO REMOVE SOLID AIRBORNE PARTICLES OF OVER SPRAY DURING SPRAY
APPLICATION.IN RESTRICTED VENTILATION AREAS USE APPROVED
RESPIRATOR DESIGN TO REMOVE A C OMBINATION OF PARTICLES AND VAPOR.
Ventilation:SUFFICIENT VENTILATION,IN VOLUME & PATTERN,SHOULD BE
PROVIDED TO KEEP AIR CONTAMINANT CONCENTRATION BELOW EXPOSURE UNITS
Protective Gloves:IMPERVIOUS FOR LONG/REPEATED EXPOSURE.
Eye Protection:SAFETY GLASSES
Other Protective Equipment:PREVENT PROLONGED SKIN CONTACT
W/CONTAMINATED CLOTHING.
Work Hygienic Practices:WASH HANDS BEFORE EATING, SMOKING OR USING THE
WASHROOM FACILITIES.
Supplemental Safety and Health
NK

Boiling Pt:B.P. Text:0 - 323F
Vapor Density:THAN AIR
Evaporation Rate & Reference:THAN ETHER
Percent Volatiles by Volume:47.58

Stability Indicator/Materials to Avoid:YES
OXIDIZING AGENTS.
Stability Condition to Avoid:EXTREME HEAT, SPARKS OR OPEN FLAMES.
Hazardous Decomposition Products:MAY PRODUCE HAZARDOUS FUMES WHEN
HEATED.

Waste Disposal Methods:DISPOSE OF IN ACCORDANCE W/FEDERAL,STATE & LOCAL
REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.